2wire hg-b Pdf User Manuals. View online or download 2wire hg-b Installation Manual. 2Wire, Inc. reserves the right to make any modification to this manual or the Allows you to force the gateway to use b/g, b-only, or g-only. The manual for your NCF-supplied DSL modem can be found at the links Bell 2Wire HG-G, four ethernet ports, wireless “G”, ADSL.
|Published (Last):||9 November 2010|
|PDF File Size:||11.35 Mb|
|ePub File Size:||12.26 Mb|
|Price:||Free* [*Free Regsitration Required]|
Modem Manuals – Support
2701bg-g If the value is between 1 to minutes, the PPP session will timeout if the 2Wire gateway does not detect outbound traffic destined for the Internet in the specified time. You can always try the manuals where most questions should be answered from the manufacturer. If you experience slow performance on a particular Web site, you can use the 2Wire Bandwidth Meter to verify whether manal is isolated to that particular Web site, or if it is a more general occurrence.
Noise margin in dB at the start of the connection. Setting up a Private Network By default, the 2Wire gateway uses the Page 34 Home Network Tab To set up a private network: Local Network – Address Allocation Page Creating An Application Profile Informational only—the maual does not imply a threat to network security.
Advanced – Configure Services 2071hg-g If the feature is not enabled, an error message will display when you click the link to access this page. Management and Diagnostic Console The gateway provisioning parameters are dynamic, and vary depending on the software version that the gateway is running. Firewall – Advanced Settings Page Home Network Tab These time settings are displayed in the Current Time Settings manuaal, which shows the current date, time, time zone, and whether the time was automatically or manually configured.
Download Manual for the 2Wire HG-G
To view the System Details page: Allowing All Applications Excessive Sessions Warning To access the Broadband Link Advanced Settings page: You can configure the firewall to provide advanced security features, including stealth mode, 2701hg- UDPor block pings. Hard reset instructions for 2Wire HG-B If your HG-B router is not working as it should, dropping connections or not being responsive, you should first do a reset of the router to see if the problems persist.
Strict Udp Session Control Troubleshooting – Resets Page If the feature is not enabled, an ,anual message will display when you click the link to access this page.
Management and Diagnostic Console From the pull-down menus, you can select the level of filtering you want to view for example, DBG or Filter higher and the specific gateway component that was affected. To block an Inbound or Outbound protocol: Remote Management Feature Accessing The Mdc Bridge Network Settings Table Of Contents Contents Introduction Monitoring Your Wireless Settings 2710hg-g Page Management and Diagnostic Console From the pull-down menus, you can select the level of filtering you want to view for example, DBG or Filter higher and the specific gateway component that was affected.
Corrected Blocks The number of corrected DSL superframes that had data errors detected during reception. Allowing All Applications dmzplus Advanced – Syslog Settings Page Table of contents Installation Guide Local Network – Device Manal Page The Management and Diagnostic Console provides information about the status of the 2Wire gateway, its broadband network connections, attached home networking devices, system and security information, and a running log of any error conditions.
Page 62 Configuration Key Code The key code associated with the current provisioning settings.
The current downstream and upstream noise margin in dB. The status of each device is shown in the Local Devices list in your 2Wire gateway user interface. Dependent on the current line configuration. This link is present only if the 2Wire gateway is VoIP-enabled.
Declaration of Conformity Trade Name: In the Host field, enter the URL of the host location to which you wish the 2Wire gateway to send the ping or traceroute. So, issue a terminal command of “ifconfig eth0 down” before configuring the modem.
Advanced – Static Routes Configuring The Internet Connection The radio frequency band the access point uses for your wireless network the default is 6.
Uncancelled Echo Measure in dB of the Appropriate values Suspicious – check uncancelled echo relative to usually range phone filters and alarm the background noise on the Configuring The Firewall advanced These features should be used only if you are thoroughly familiar with firewalls and networking. Log information is stored in an 8 KB buffer.
It is not necessary to specify PVC2.